PRODUCT INSTRUCTIONS
DOC-IFU-FLUX-10CC-001-EN · Rev. A · 2026
No-Clean Soldering Flux
No-Clean Rosin Flux Paste · Lead-Free · 10cc Syringe
Lead-Free
Halogen-Free
No-Clean
Non-Corrosive
RoHS
10cc
TYPE
No-Clean Rosin
CLASS
ROL0
HALIDE
Halide-Free
VOLUME
10cc
1
APPLICATIONS
PCB Soldering
SMD / BGA Rework
Desoldering (with wick)
Tinning Wires & Tips
Component Repair
Lead-Free & Leaded
2
SPECIFICATIONS
Flux TypeNo-Clean Rosin Paste
BaseHigh-purity rosin / resin
ClassificationROL0 (IPC J-STD-004)
Halide ContentHalide-free <0.05% (IPC J-STD-004 ROL0)
Halogen ContentNo intentionally added halogens
Net Content10cc (10 ml) · ~10 g
CorrosivityNon-corrosive · non-conductive (dry)
RoHS CompliantYes (Lead-Free)
3
COMPATIBILITY
Works with most metals & solder types
Compatible Metals
CopperGoldTinIron / SteelBrass
Compatible Solders
Lead-Free SACSn63/Pb37Sn42/Bi58 Low-Temp
4
STORAGE
STORAGE TEMP
10–32°C
50–90°F · no fridge needed
SHELF LIFE
12 Months
Unopened · 6 months after opening
KEEP
Cool & Dry
Away from heat/flame
After Use: Remove the needle, wipe the tip, and reseal the cap. Store upright in a cool, dry place — no refrigeration required. Do not use past the EXP date.
5
TROUBLESHOOTING
Flux is thick / hard to push
Let it sit at room temperature; apply steady pressure on the push rod. Use a larger needle for general work.
Sticky residue after soldering
Normal for no-clean rosin. Use less flux; if a clean finish is wanted, wipe with 99% IPA and a brush/Q-tip.
Poor wetting / dull joint
Pad oxidized or not enough flux/heat. Apply a little more flux and ensure the iron tip is 300–380°C.
Needle clogged
Clear with a fine wire or replace the needle. Reseal the cap after every use.
6
HOW TO USE
1
Apply flux to the joint
Fit a needle and gently push the rod to lay a thin layer of flux on the pads, lead or joint. A little goes a long way.
Pushing design — smooth flow, no waste
2
Hand soldering
Touch the heated iron (300–380°C) and solder wire to the fluxed joint; the solder wets and flows in cleanly.
3
SMD / BGA rework
Apply flux to the pads, place the component, then reflow with a hot-air station. Flux improves wetting and self-alignment.
4
Desoldering
Apply flux over the joint, lay desoldering wick on top, and press with the iron — the wick draws up the molten solder.
Flux makes wick soak up solder faster
5
Reseal after use
Remove the needle, wipe the tip and screw the cap back on. Store upright at room temperature.
6
Clean if desired
No-clean residue is non-conductive and may stay on the board. For a clean look, remove with 99% IPA.
7
SAFETY INFORMATION
Warning
WARNING
GHS07
Hazard statements — H315 Causes skin irritation. H317 May cause an allergic skin reaction (rosin / colophony). H319 Causes serious eye irritation. H335 May cause respiratory irritation.
Precautionary statements — P261 Avoid breathing dust or fumes. P264 Wash hands and exposed skin thoroughly after handling. P271 Use only outdoors or in a well-ventilated area. P280 Wear protective gloves, eye protection and protective clothing. P302+P352 IF ON SKIN: Wash with plenty of soap and water. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P333+P313 If skin irritation or rash occurs: Get medical advice or attention. P337+P313 If eye irritation persists: Get medical advice or attention. P362+P364 Take off contaminated clothing and wash it before reuse. P403+P233 Store in a well-ventilated place. Keep container tightly closed. P501 Dispose of contents and container in accordance with local, regional and national regulations.
KEEP OUT OF REACH OF CHILDREN.
DO NOT
✗ Breathe concentrated fumes — always solder with ventilation or fume extraction.
✗ Apply direct flame to the syringe or store it near heat.
✗ Use for medical, food-contact or oral applications.
FIRST AID — Skin: wash with soap and water. Eyes: rinse with water for 15 minutes. Inhaled: move to fresh air. Swallowed: rinse mouth, do NOT induce vomiting. If symptoms persist, get medical advice. Poison Control 1-800-222-1222 (USA).
STORAGE — Store sealed at 10–32 °C (50–90 °F) — no refrigeration needed. Shelf life 12 months unopened; 6 months after opening.
For professional and hobbyist electronics assembly and repair. Not for human consumption or food-contact use. Transport classification: see SDS Section 14.
DISTRIBUTED BY
LINGSKO LLC
CASPER WY 82609 USA
Full Safety Data Sheet
tinvoa.co/sds/flux
SKU TFX-RO-10CC · DOC-IFU-FLUX-10CC-001-EN · Rev. A · 2026 · TDS: tinvoa.co/tds/flux
www.tinvoa.co
[email protected]