PRODUCT INSTRUCTIONS
DOC-IFU-TACKYFLUX-10CC-001-EN · Rev. A · 2026
No-Clean Tacky Flux
High-Tack Rosin Flux Paste · Lead-Free · 10cc Syringe
High-Tack
Lead-Free
Halogen-Free
No-Clean
Non-Corrosive
RoHS
10cc
FLUX ONLY — CONTAINS NO SOLDER ALLOY
TYPE
High-Tack Rosin
CLASS
ROL0
HALIDE
Halide-Free
VOLUME
10cc
1
APPLICATIONS
BGA / QFN / LGA Reballing
Holding Parts Through Reflow
Stencil Printing
Pin Transfer
Fine-Pitch Rework
Lead-Free & Leaded
2
SPECIFICATIONS
Flux TypeNo-Clean Rosin Paste · High-Tack
BaseHigh-purity rosin / resin
ClassificationROL0 (IPC J-STD-004)
Halide ContentHalide-free <0.05% (IPC J-STD-004 ROL0)
Halogen ContentNo intentionally added halogens
Net Content10cc (10 ml) · ~10 g
CorrosivityNon-corrosive · non-conductive (dry)
RoHS CompliantYes (Lead-Free)
3
COMPATIBILITY
Works with most metals & solder types
Compatible Metals
CopperGoldTinIron / SteelBrass
Compatible Solders
Lead-Free SACSn63/Pb37Sn42/Bi58 Low-Temp
4
STORAGE
STORAGE TEMP
10–32°C
50–90°F · no fridge needed
SHELF LIFE
12 Months
Unopened · 6 months after opening
KEEP
Cool & Dry
Away from heat/flame
After Use: Remove the needle, wipe the tip, and reseal the cap. Store upright in a cool, dry place — no refrigeration required. Do not use past the EXP date.
5
TROUBLESHOOTING
Stiffer to push than standard flux
Normal — a high-tack paste carries more solids. Bring it to room temperature, fit an 18–20 G needle and use steady pressure. Do not warm it with a heat gun.
Part shifts or balls roll off before reflow
The layer is too thin, or it has already skinned over. Lay an even film and seat the part while the flux is still wet.
Residue harder to remove than standard flux
Also from the higher solids. No-clean residue may be left in place; for a clean finish use warm 99% IPA with a brush.
Flux skins over in the syringe
Remove the needle, wipe the tip and reseal the cap after every use. Store upright and capped.
6
HOW TO USE
1
Lay an even film of flux
Fit a needle and push gently to spread a thin, even layer over the pads or the ball side of the package. Even coverage matters more than quantity.
Even film = even tack
2
Seat the component
Place the part while the flux is still wet. The tack holds it in position through handling and the reflow ramp — no separate adhesive needed.
3
Reballing with a stencil
Print or pin-transfer flux through the preform stencil, drop the balls, then reflow. The tack keeps the array registered while the board heats.
4
Reflow
Follow the reflow profile of the solder alloy you are using — this flux does not set the profile. Hot-air rework and oven reflow are both suitable.
Profile comes from the alloy, not the flux
5
Reseal after use
Remove the needle, wipe the tip and screw the cap back on. Store upright at room temperature.
6
Clean if desired
No-clean residue is non-conductive and may stay on the board. For a clean finish, remove with warm 99% IPA and a brush.
7
SAFETY INFORMATION
Warning
WARNING
GHS07
Hazard statements — H315 Causes skin irritation. H317 May cause an allergic skin reaction (rosin / colophony). H319 Causes serious eye irritation. H335 May cause respiratory irritation.
Precautionary statements — P261 Avoid breathing dust or fumes. P264 Wash hands and exposed skin thoroughly after handling. P271 Use only outdoors or in a well-ventilated area. P280 Wear protective gloves, eye protection and protective clothing. P302+P352 IF ON SKIN: Wash with plenty of soap and water. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing. P333+P313 If skin irritation or rash occurs: Get medical advice or attention. P337+P313 If eye irritation persists: Get medical advice or attention. P362+P364 Take off contaminated clothing and wash it before reuse. P403+P233 Store in a well-ventilated place. Keep container tightly closed. P501 Dispose of contents and container in accordance with local, regional and national regulations.
KEEP OUT OF REACH OF CHILDREN.
DO NOT
✗ Breathe concentrated fumes — always solder with ventilation or fume extraction.
✗ Apply direct flame to the syringe or store it near heat.
✗ Use for medical, food-contact or oral applications.
FIRST AID — Skin: wash with soap and water. Eyes: rinse with water for 15 minutes. Inhaled: move to fresh air. Swallowed: rinse mouth, do NOT induce vomiting. If symptoms persist, get medical advice. Poison Control 1-800-222-1222 (USA).
STORAGE — Store sealed at 10–32 °C (50–90 °F) — no refrigeration needed. Shelf life 12 months unopened; 6 months after opening.
For professional and hobbyist electronics assembly and repair. Not for human consumption or food-contact use. Transport classification: see SDS Section 14.
DISTRIBUTED BY
LINGSKO LLC
CASPER WY 82609 USA
Full Safety Data Sheet
tinvoa.co/sds/tacky-flux
SKU TFX-RT-10CC · DOC-IFU-TACKYFLUX-10CC-001-EN · Rev. A · 2026 · TDS: tinvoa.co/tds/tacky-flux
www.tinvoa.co
[email protected]